.32-20 Winchester

Last updated
.32-20 Winchester
32-20--32ACP.JPG
.32-20 (Left), .32 ACP (Right)
TypeRifle, revolver
Place of originUnited States
Production history
Designer Winchester Repeating Arms Company
Designed1882
Produced1882–present
Specifications
Case type Rimmed, bottleneck
Bullet diameter.3125 in (7.94 mm)
Land diameter.3051 in (7.75 mm)
Neck diameter.327 in (8.3 mm)
Shoulder diameter.342 in (8.7 mm)
Base diameter.354 in (9.0 mm)
Rim diameter.408 in (10.4 mm)
Rim thickness.065 in (1.7 mm)
Case length1.315 in (33.4 mm)
Overall length1.592 in (40.4 mm)
Rifling twist1 in 20 in (510 mm)
Primer typeSmall pistol
Maximum CUP16,000 [1] CUP
Ballistic performance
Bullet mass/typeVelocityEnergy
85 gr (6 g) JHP1,100 ft/s (340 m/s)228 ft⋅lbf (309 J)
115 gr (7 g) CL900 ft/s (270 m/s)207 ft⋅lbf (281 J)
100 gr (6 g) CL (Rifle)1,210 ft/s (370 m/s)325 ft⋅lbf (441 J)
Source(s): "Cartridges of the World", Chuck Hawks [2] [3]
disassembled .32-20 Winchester cartridge with 100 grain lead bullet 32-20-disassembled.jpg
disassembled .32-20 Winchester cartridge with 100 grain lead bullet

The .32-20 Winchester, also known as .32 WCF (Winchester center fire), was the first small-game lever-action cartridge that Winchester produced. [4] It was initially introduced as a black-powder cartridge in 1882 for small-game, varmint hunting, and deer. [5] [6] Colt produced a single-action revolver chambered for this cartridge a few years later. [7]

Contents

The name .32-20 refers to the 32 caliber bullet of .312-inch-diameter (7.9 mm) and standard black-powder charge of 20 grains (1.3 g).

Performance

This cartridge was sometimes used for deer hunting in the past, and William Lyman, the designer of rifle sights, said of it: "For large game, of course, a .32-20 W.C.F. cartridge is rather small, but it comes nearer to being an all-around cartridge in my opinion than any other." [8] Many now consider it too light and low-powered for deer and better suited to small game and metallic silhouette. It has a good reputation for accuracy in rifles as well as the few handguns that have been chambered for it. [5] [6] Because of its low power, it destroys very little meat, making it a good hunting round for appropriately sized game, up to about 100 yards (91 m).[ citation needed ] Although it is an inexpensive cartridge to reload, [3] care must be taken by the reloader because of the extremely thin walls of the cartridge case. [9] Energy and pressure levels for handloading are determined based on the strength and condition of the firearm action to be used. Because most firearms chambered for this cartridge are older (e.g. early model Winchester Model 73 and 92 rifles as well as older Colt and Smith & Wesson revolvers) factory ammunition usually has reduced pressures from what can be achieved through handloading. Most factory ammunition exhibits ballistics of about 1,200 ft/s (370 m/s) and 325 ft⋅lbf (441 J) of energy at the muzzle with a 100-grain (6.5 g) bullet from an 18 to 20 inch rifle barrel. The performance characteristics of the cartridge listed in the sidebar should be considered maximum performance parameters obtainable, and even then only with a modern weapon designed for higher pressure loads. Factory-type loads - and reloads mimicking factory type loads - are the safe maximum loads for use in older firearms. Few, if any, companies still manufacture firearms in this caliber.

Daughter cartridges

The .25-20 Winchester cartridge is simply a necked-down version of the .32-20. [4] In addition, the .218 Bee was created using the .32-20 as its parent cartridge.

The .32-20 cartridge case has been used to create usable ammunition for the Nagant M1895. This is accomplished by removing .01" from the rim thickness and sizing the case in a specific reloading die (Lee Nagant 3 die set). The ammunition produced is functional and easy to reload; however, .32-20 brass does not provide a gas seal as it is not long enough to protrude past the Nagant cylinder. [10] The .32-20 cartridge case can also be used to create 8mm French Ordnance ammunition for use in the Modèle 1892 revolver.

Currently, the .32-20 is used and modified by shooters in the UK and Australia for the .310 Cadet cartridge. Modifications involve length resizing and in most cases reducing the rim thickness. Due to the .310 using a heeled projectile, the neck thickness is not too much of a concern, after first being case length resized to 1.075" (27.3 mm). Most .310 cadet chambered rifles need to have the rim of the .32-20 case reduced from 0.065" to under 0.045" (1.7 mm to 1.14 mm), to allow proper head spacing and operation of rifle. However, in the instance of a lever action .32-20 fitted with a .310 barrel, the rifle will cycle better without the case rim thickness being reduced. As home reloading is the main option for the .310, many shooters play with different case length reduction of the .32-20, anywhere from 0.875'' to 1.185'' (22.23 mm to 30.10 mm).[ citation needed ]

See also

Related Research Articles

<span class="mw-page-title-main">Cartridge (firearms)</span> Pre-assembled firearm ammunition consisting of a casing, projectile, propellant, and primer

A cartridge, also known as a round, is a type of pre-assembled firearm ammunition packaging a projectile, a propellant substance and an ignition device (primer) within a metallic, paper, or plastic case that is precisely made to fit within the barrel chamber of a breechloading gun, for convenient transportation and handling during shooting. Although in popular usage the term "bullet" is often used to refer to a complete cartridge, the correct usage only refers to the projectile.

<span class="mw-page-title-main">Centerfire ammunition</span> Type of ammunition that is commonly found in small-, medium-, and large-caliber firearms

A center-fire is a type of metallic cartridge used in firearms, where the primer is located at the center of the base of its casing. Unlike rimfire cartridges, the centerfire primer is typically a separate component seated into a recessed cavity in the case head and is replaceable by reloading the cartridge.

<span class="mw-page-title-main">.40 S&W</span> Pistol cartridge

The .40 S&W (10.2x22mm) is a rimless pistol cartridge developed jointly by American firearms manufacturers Smith & Wesson and Winchester in 1990. The .40 S&W was developed as a law enforcement cartridge designed to duplicate performance of the Federal Bureau of Investigation's (FBI) reduced-velocity 10mm Auto cartridge which could be retrofitted into medium-frame semi-automatic handguns. It uses 0.40-inch (10 mm) diameter bullets ranging in weight from 105 to 200 grains.

<span class="mw-page-title-main">.357 Magnum</span> Revolver cartridge

The .357 Smith & Wesson Magnum, .357 S&W Magnum, .357 Magnum, or 9×33mmR is a smokeless powder cartridge with a 0.357 in (9.07 mm) bullet diameter. It was created by Elmer Keith, Phillip B. Sharpe, and Douglas B. Wesson of firearm manufacturers Smith & Wesson and Winchester. The .357 Magnum cartridge is notable for its highly effective terminal ballistics.

<span class="mw-page-title-main">.45 Colt</span> Revolver cartridge designed by the U.S. Army

The .45 Colt (11.43×33mmR), is a rimmed, straight-walled, handgun cartridge dating to 1872. It was originally a black-powder revolver round developed for the Colt Single Action Army revolver. This cartridge was adopted by the U.S. Army in 1873 and served as an official US military handgun cartridge for 19 years, before being replaced by the .38 Long Colt in 1892.

<span class="mw-page-title-main">.44 Magnum</span> Revolver cartridge designed by Elmer Keith and Smith & Wesson (S&W)

The .44 Remington Magnum, also known as .44 Magnum or 10.9x33mmR, is a rimmed, large-bore cartridge originally designed for revolvers and quickly adopted for carbines and rifles. Despite the ".44" designation, guns chambered for the .44 Magnum round, its parent case, the .44 Special, and its parent case, the .44 Russian all use 0.429 in (10.9 mm) diameter bullets. The .44 Magnum is based on the .44 Special case but lengthened and loaded to higher pressures for greater velocity and energy.

<span class="mw-page-title-main">.44 Special</span> Revolver cartridge designed by Smith & Wesson (S&W)

The .44 Smith & Wesson Special, also commonly known as .44 S&W Special, .44 Special, .44 Spl, .44 Spc, or 10.9×29mmR, is a smokeless powder center fire metallic revolver cartridge developed by Smith & Wesson in 1907 as the standard chambering for their New Century revolver, introduced in 1908.

<span class="mw-page-title-main">.410 bore</span> Shotgun bore designed by Charles Eley and William Eley

The .410 bore (10.4 mm) is one of the smallest caliber of shotgun shell commonly available. A .410 bore shotgun loaded with shot shells is well suited for small game hunting and pest control. The .410 started off in the United Kingdom as a garden gun along with the .360 and the No. 3 bore (9 mm) rimfire, No. 2 bore (7 mm) rimfire, and No. 1 bore (6 mm) rimfire. .410 shells have similar base dimensions to the .45 Colt cartridge, allowing many single-shot firearms, as well as derringers and revolvers chambered in that caliber, to fire .410 shot shells without any modifications.

The .256 Winchester Magnum is a firearms cartridge developed by Winchester, and was produced by necking-down a .357 Magnum cartridge to .257 diameter. It was designed for shooting small game and varmints.

<span class="mw-page-title-main">.38-40 Winchester</span> American pistol cartridge

The .38-40 Winchester (10.17x33mmR) is actually a .40 caliber (10 mm) cartridge shooting .401 in (10.2 mm) caliber bullets. The cartridge was introduced by Winchester in 1874 and is derived from their .44-40 Winchester. This cartridge was introduced for rifles, but in its reintroduction for cowboy action shooting it has seen some popularity as a revolver cartridge. It is not particularly well suited to hunting larger game, but it was popular when it was introduced, along with the previous .44-40 Winchester, for deer hunting. It can be used successfully on smaller game animals, and for self-defense. Current loadings are intended for revolvers.

<span class="mw-page-title-main">.44-40 Winchester</span> American firearms cartridge

The .44-40 Winchester, also known as .44 Winchester, .44 WCF, and .44 Largo, was introduced in 1873 by the Winchester Repeating Arms Company. It was the first metallic centerfire cartridge manufactured by Winchester, and was promoted as the standard chambering for the new Winchester Model 1873 rifle. As both a rifle and a handgun caliber, the cartridge soon became widely popular, so much so that the Winchester Model 1873 rifle became known as "The gun that won the West."

<span class="mw-page-title-main">Wildcat cartridge</span> Custom cartridge for firearms

A wildcat cartridge, often shortened to wildcat, is a custom cartridge for which ammunition and/or firearms are not mass-produced. These cartridges are often created in order to optimize a certain performance characteristic of an existing commercial cartridge, or may merely be intended as novelty items.

<span class="mw-page-title-main">.30-40 Krag</span> First cartridge adopted by the US Army that was designed for smokeless powder.

The .30-40 Krag, also known as the .30 U.S. and .30 Army, was a rifle cartridge developed in the early 1890s to provide the U.S. armed forces with a smokeless powder cartridge suited for use with modern small-bore repeating rifles to be selected in the 1892 small arm trials. Since the cartridge it was replacing was the .45-70 Government, the new cartridge was considered small-bore at the time. The rifle ultimately selected for use by the Army was the Krag–Jørgensen, formally adopted as the M1892 Springfield. The cartridge was also used in the M1893, M1895, M1897, and M1900 Gatling guns.

A rim is an external flange that is machined, cast, molded, stamped, or pressed around the bottom of a firearms cartridge. Thus, rimmed cartridges are sometimes called "flanged" cartridges. Almost all cartridges feature an extractor or headspacing rim, in spite of the fact that some cartridges are known as "rimless cartridges". The rim may serve a number of purposes, including providing a lip for the extractor to engage, and sometimes serving to headspace the cartridge.

<span class="mw-page-title-main">.30-30 Winchester</span> Rifle cartridge designed by the Winchester Repeating Arms Company

The .30-30 Winchester cartridge was first marketed for the Winchester Model 1894 lever-action rifle in 1895. The .30-30, as it is most commonly known, along with the .25-35 Winchester, was offered that year as the United States' first small-bore sporting rifle cartridges designed for smokeless powder. Since its introduction, it has been utilized alongside the development of flatter shooting cartridges, most prominently those derived from designs subsidized by interest in military expenditures, yet the .30-30 has remained in widespread use almost entirely because of reliable effectiveness in civilian applications, proven by putting food on the table for millions of people within a practical range of hunting situations.

<span class="mw-page-title-main">Overpressure ammunition</span> Type of small arms ammunition

Overpressure ammunition, commonly designated as +P or +P+, is small arms ammunition that has been loaded to produce a higher internal pressure when fired than is standard for ammunition of its caliber, but less than the pressures generated by a proof round. This is done typically to produce ammunition with higher muzzle velocity, muzzle energy, and stopping power, such as ammunition used for security, defensive, or hunting purposes. Because of this, +P ammunition is typically found in handgun calibers which might be used for paramilitary forces, armed security, and defensive purposes.

<span class="mw-page-title-main">.25-20 Winchester</span> Rifle cartridge

The .25-20 Winchester, or WCF, was developed around 1895 for the Winchester Model 1892 lever action rifle. It was based on necking down the .32-20 Winchester. In the early 20th century, it was a popular small game and varmint round, developing around 1,460 ft/s with 86-grain bullets. But two years earlier Marlin Firearms Co. had already necked down the .32-20 Winchester, and called it the .25-20 Marlin. It was first chambered in Model 1889 lever action Marlins long before Winchester did the same thing and put their name on the .25-20.

<span class="mw-page-title-main">7.62×38mmR</span> Russian revolver cartridge

7.62×38mmR is an ammunition cartridge designed for use in the Russian Nagant M1895 revolver.

.32 caliber is a size of ammunition, fitted to firearms with a bore diameter of 0.32 inches (8.1 mm).

<span class="mw-page-title-main">.351 Winchester Self-Loading</span> Rifle cartridge

The .351 Winchester Self-Loading is an American rifle cartridge designed in 1906.

References

  1. Saami pressures. (n.d.). Retrieved May 3, 2023, from https://leverguns.com/articles/saami_pressures.htm
  2. "The .32-20 Winchester". Chuck Hawks. 2013.
  3. 1 2 Barnes, Frank C. (1997) [1965]. McPherson, M.L. (ed.). Cartridges of the World (8th ed.). DBI Books. pp. 64, 91. ISBN   0-87349-178-5.
  4. 1 2 "Levergun loads: the .25-20 Winchester" by John Taffin, Guns Magazine, April 2004
  5. 1 2 ".32-20 Winchester (HV-92) Archived 2005-05-22 at the Wayback Machine " from Accurate Powder
  6. 1 2 "The .32-20 Winchester" by Chuck Hawks
  7. "32-20 Winchester Centerfire 1882" by Paco Kelly at Leverguns.com
  8. Townsend Whelen (1918). The American Rifle: A Treatise, a Text Book, and a Book of Practical Instruction in the Use of the Rifle. Century Company. p. 256.
  9. People who do hand load the .32-20 feel this is not problematic, and if usual care is taken, there is no special problem with the case.
  10. Fisher, George N. (November 9, 2002). "M1895 Nagant Revolver Reloading Project". Makarov.com. Retrieved December 8, 2012.
  11. 32-20 Blues